From professionals for professionals – screed laying with PCI products

• For indoor and outdoor use.
• For floors.
• Impregnating and strengthening concrete and screed surfaces.
• Increase of wear resistance in repair shops, manufacturing rooms and similar.
• Modification of concrete and screed surfaces in industrial plants, warehouses and similar to help binding sand and dust on the surface.

• For indoor and outdoor use.
• For the production of colored finishes resistant to wear and chemicals for concrete floors and cement screeds. Mastic asphalt screeds for indoor use only.
• For floors in manufacturing areas and warehouses subject to light to medium mechanical loads; can be exposed to vehicles with pneumatic tyres.
• For areas subject to moderate chemical exposure.

• For indoor and outdoor use.
• Highly wear-resistant and chemical-resistant coating on concrete surfaces and cement screeds.
• For all industrial areas such as warehouses, assembly halls, production halls, ramps and roadways, also on safety kerbs and forklifts in operation.
• For casting the pool edge in swimming pools.
• Can be applied by roller as a sealing from 0.3 mm.
• Can be applied as a coating from 1 mm layer thickness.
• For surfaces subject to an increased mechanical use caused by impact filled with silica sand 1 : 1 up to a layer thickness of 3 mm.

• For indoor and outdoor use.
• For producing wear-resistant and chemical-resistant coatings in all industrial areas.
• Crack-bridging, self-levelling coating on cementitious substrates and mastic asphalt.
• PCI Apoten PU can be mixed with silica sand, mixing ratio up to 1 : 0.3.

• For floors.
• For indoor and outdoor use.
• For the production of highly wear resistant and chemical resistant screeds on concrete floors and cement screeds
  - for industrial floors, workshops and stables subject to high chemical and/or mechanical loads,
  - in breweries, dairies and other wet locations.
• For grouting and tamping.
• For water permeable mono-granular mortar for the installation of kerbstones on bridges.
• For repair work on concrete floors and slabs.

• For indoor and outdoor use.
• Mortar additive for render and gauged render.
• For producing cement mortar and cement screed with reduced absorption of water and low penetration depth of water, with plasticising properties.
• Also suitable for a heated screed.

• For indoor and outdoor use.
• For walls and floors.
• Primer for PCI sealings and PCI coatings on cementitious substrates, mastic asphalt screeds, ceramic tiles, synthetic resin coatings and wooden substrates.
• Primer for floors in the interior before applying floor levellers/fairing coats, also when subsequently gluing parquet flooring on
  - concrete floors, cement screeds, calcium sulphate screeds, magnesite screeds
  - mastic asphalt screeds
  - ceramic tiles and synthetic resin coatings
  - wooden substrates
  - substrates with residues of dispersion, reaction resin, water soluble (e.g. spent sulphite liquor adhesive) and bitumen adhesives.
• Suitable as leveller and/or fairing coat when mixed with silica sand.
• As a binding agent for producing screeds, repair mortars and drain mortars based on epoxy resin.
• Suitable for the use on ships; meets the requirements of Marine Equipment Directive (MED) 96/98/EC.

• For indoor and outdoor use.
• For walls and floors.
• Primer for PCI sealings and PCI coatings on cementitious substrates, mastic asphalt screeds, ceramic tiles, synthetic resin coatings and wooden substrates.
• Primer for floors in the interior before applying floor levellers/fairing coats, also when subsequently gluing parquet flooring on
  - concrete floors, cement screeds, calcium sulphate screeds, magnesite screeds
  - mastic asphalt screeds
  - ceramic tiles and synthetic resin coatings
  - wooden substrates
  - substrates with residues of dispersion, reaction resin, water soluble (e.g. spent sulphite liquor adhesive) and bitumen adhesives.
• Suitable as leveller and/or fairing coat when mixed with silica sand.
• As a binding agent for producing screeds, repair mortars and drain mortars based on epoxy resin.
• Suitable for the use on ships; meets the requirements of Marine Equipment Directive (MED) 96/98/EC.

• For indoor and outdoor use.
• For floors.
• Transparent, lightfast and matt top coat on PCI sealings and coatings.
• For floors in industrial companies, warehouses and commercial businesses.
• For chemical resistant sealing of floors that have been given a decorative look with PCI Farbchips.

• For indoor and outdoor use.
• For absorbent and low-absorbent concrete and screed substrates.
• As special primer for PCI Zemtec 1K, PCI Zemtec 180, PCI Periplan, PCI Periplan Extra, PCI Periplan Plus, PCI Periplan Fein, PCI Periplan Multi and PCI Periplan White.
• As special primer for anhydrite screeds, mastic asphalt screeds, magnesite screeds for floor levelers and tile adhesives. 
• As special primer for wooden floorboards, particle boards as well as OSB boards.
• As special primer for non-absorbent substrates such as ceramic tiles for subsequent floor leveling compounds.
• Suitable for the use on ships; meets the requirements of Marine Equipment Directive (MED) 96/98/EC.

• For indoor and outdoor use.
• For areas exposed to permanent wetness.
• For fast-curing bonded screeds and screeds installed on an isolating or insulating layer.
• Suitable for heated screeds.
• For layer thickness from 20 to 80 mm.
• Very low emissions, GEV-EMICODE EC 1 PLUS.

• For indoor and outdoor use.
• For areas exposed to permanent wetness.
• For light bonded screeds and screeds installed on an isolating or insulating layer.
• Light mortar for refurbishment of concrete floors and cement screeds.
• For layer thickness from 20 to 80 mm.
• Very low emissions, GEV-EMICODE EC 1 PLUS.

• For indoor and outdoor use.
• Suitable for direct use.
• For areas exposed to permanent wetness.
• For fast-curing bonded screeds and screeds installed on an isolating layer or insulation layer.
• Suitable for heated screeds.
• As repair mortar for quick repairs of industrial floors.
• For layer thickness from 20 to 120 mm.
• Very low emissions, GEV-EMICODE EC1 PLUS.

• For indoor and outdoor use, also for direct use.
• For areas exposed to permanent wetness.
• For fast track bonded screeds and screeds installed on an isolating or insulating layer.
• Suitable for heated screeds.
• As repair mortar for concrete floors and cementitious screeds.
• For layer thickness from 20 to 80 mm.

• For indoor and outdoor use.
• For producing fast track
  - screeds on an isolating layer or insulating layer
  - bonded screeds.
• Suitable for heated screeds.

• For producing bonded screeds and screeds on an isolating layer or insulating layer (also heated screeds).
• For indoor and outdoor use, also suitable for direct use.
• For areas exposed to permanent wetness.
• For bonded screeds to be covered at an early stage.

• For outdoor use, floors.
• For producing crack-bridging coatings resistant to UV, weather conditions and mechanical loads to be applied to concrete surfaces, cement screeds and mastic asphalt screeds such as balconies, terraces and access balconies.
• The coating can be given a decorative finish by sprinkling coloured chips.

• For indoor use.
• On concrete floors, floating screeds or screeds on an isolating layer, wooden floorboards and particle boards, old ceramic tiles and natural stones.
• For the transition area floor/wall to prevent sound transmission when applying flowable floor levellers (e.g. PCI Periplan, PCI Periplan Fein), non-sag fairing coats and tile adhesives (e.g. PCI Flexmörtel, PCI Nanolight, PCI Nanoflott light) or parquet or flooring adhesives to all suitable substrates.
• For preventing three-sided adhesion at elastic edge joints.
• Especially for renovation works.

• For indoor use as directly usable, self-leveling, wear-resistant cementitious floor leveler.
• For outdoor use under top coverings.
• For residential, commercial and industrial buildings.
• For layer thickness from 3 - 40 mm.
• For leveling and surface repair of rough, irregular concrete floors, cement screeds, anhydrite screeds, mastic asphalt screeds and ceramic tiles.
• Also for heated screeds.

• For outdoor use, floors.
• For producing crack-bridging coatings resistant to UV, weather conditions and mechanical loads to be applied to concrete surfaces, cement screeds and mastic asphalt screeds such as balconies, terraces and access balconies.
• The coating can be given a decorative finish by sprinkling colored chips.

• For floors.
• For outdoor use.
• For producing permeable screeds free from efflorescence, for balconies and terraces with a low height.
• On drainage mats, waterproofing membranes such as PCI BT 21 „all-weather“ waterproofing membrane and waterproofing slurries such as PCI Seccoral.
• For subsequent laying of tiles, flagstones and natural stones.
• Installation height from 20 mm upwards.
• For floor surfaces subject to pedestrian traffic such as terraces and balconies.

• For indoor and outdoor use.
• Load-transferring, supporting, force-transmitting bond between concrete foundations and machines, steel bed plates, steel rails (crane track rails) and high shelving pillars.
• Precise grouting of machines, turbines, pumps and generators.
• Force-transmitting grouting of pre-fabricated concrete pillars in hole footings.
• Void-free bond between components and non-reinforced concrete or reinforced concrete.
• For grouting heights from 5 to 100 mm.

• For indoor and outdoor use.
• For floors.
• Grouting and bedding of machines, bridge bearings and pillars.
• Electrically isolated grouting of railway tracks.
• Precision grouting and bedding of crane rails and turbines.
• Grouting of guide rails and guardrail posts, pillars in hall and shelving construction.
• Grouting of voids and gaps.
• Force-transmitting bond of concrete with concrete and concrete with metal.
• Repair of heavy-duty floor surfaces.

• For indoor and outdoor use.
• For friction-locked, void-free grouting of anchoring and mounting holes (e.g. prefabricated concrete elements), rails for tramways, railways and craneways, and high-bay shelving supports.
• For grouting manhole covers as well as joints between manhole surround and cone or adjusting ring following the raising of the surround.
• For grouting holes and cavities with a cross section from 5 to 50 mm (undiluted), up to a cross section of 100 mm when mixed with gravel, grain size 4 - 8 mm.

• For bedding structures made of steel and concrete.
• For connecting concrete with steel and precast concrete.
• For bedding wooden frames to produce a force-fit bond with the floor slab.
• For grouting vertical and horizontal precast concrete construction joints.
• For grouting cavities and gaps.
• For indoor and outdoor use.
• For layer thickness from 15 to 50 mm.
• Can be blended with gravel for higher layer thickness (4 to 8 mm).

• For indoor and outdoor use.
• Load-transferring, supporting, force-transmitting bond between concrete foundations and machines, steel bed plates, steel rails and high shelving pillars, drain gutters, steel railings.
• Force-transmitting grouting of pre-fabricated concrete pillars in hole footings.Void-free bond between components and non-reinforced concrete or reinforced concrete.
• For grouting heights from 20 to 80 mm, up to 180 mm when blended with gravel.

• For indoor and outdoor use.
• Load-transferring, supporting, force-transmitting bond between concrete foundations and machines, steel bed plates, steel rails (crane track rails) and high shelving pillars.
• Precise grouting of machines, turbines, pumps and generators.
• Force-transmitting grouting of pre-fabricated concrete pillars in hole footings.
• Void-free bond between components with non-reinforced concrete or reinforced concrete.
• For grouting height from 40 to 150 mm.

• For indoor and outdoor use.
• For walls and floors.
• Bonding slurry for the repair mortar PCI Repament, the ready-mixed, fast-setting screed mortars PCI Novoment M1 plus/M3 plus, and the drain and screed mortar PCI Pavifix DM as well as usual sand-cement mortars.
• Bonding slurry for the installation of fast setting screeds based on binder PCI Novoment Z1 and PCI Novoment Z3 as well as for usual cement screeds.
• Bonding slurry for the production of bonded coverings in industrial and commercial areas, also for sloped screeds on balconies and terraces.
• Bonding slurry for non-translucent natural stones insensitive to staining.

• For indoor and outdoor use.
• Corrosion protection of reinforcing bars in the repair of reinforced concrete components.
• Bonding slurry between cured concrete or masonry and green concrete and mortar.

• For indoor and outdoor use.
• For walls and floors.
• For the quick repair of concrete floors and cement screeds, concrete constructions and industrial floors; e.g. at concrete walls, breastworks, treads, concrete roads, etc.
• For producing small-surface industrial floors, bonded screeds and factory roads.
• For layer thickness from 5 - 20 mm (without coarse aggregate), from 20 - 40 mm blended with coarse aggregate.

• For indoor and outdoor use.
• For bonded screeds and screeds on an isolating and insulating layer.
• For repair work and sloped surfaces.
• High strength.
• For layer thickness from 10 - 100 mm.
• Very low emissions, EC1 Plus R.

• For indoor and outdoor use.
• For small screed surfaces and grouting work.
• Consistency can be adjusted by changing the water quantity.
• Highly resistant, fast-setting mortar for repairing concrete floors, cement screeds, concrete construction, stairs and industrial floors.
• Bonded screeds: for layer thickness from 10 - 100 mm.
• Screeds on isolation layer: for layer thickness from 40 - 100 mm.
• Very low emissions, EC 1 PLUS.

• For indoor and outdoor use.
• For producing monolithic, cement based concrete floors.
• For abrasion resistant concrete surfaces exposed to grinding conditions.
• Forms a highly abrasion resistant, wear resistant, smooth dry shake surface homogeneously embedded in the concrete surface.
• For industrial floors and commercial floors.

• For indoor and outdoor use.
• For walls and floors.
• Colored and matt sealing of concrete floors and cement screeds.
• For floors in industrial firms, warehouses, commercial businesses and garages subject to light to medium mechanical stress, floors must be resistant to chemicals.
• For chemical-resistant, anti-slip sealing of high strength synthetic resin screeds and coatings.

• For indoor and outdoor use.
• For direct use, self leveling, high strength, cementitious flowable screed.
• For industrial areas and residential buildings, e.g. storage rooms and workshops.
• For layer thickness from 15 to 80 mm.
• For heavy-duty use also in outdoor areas.

• For indoor use.
• Cementitous floor leveler for irregular concrete floors and cement screed surfaces.
• Suitable for exposure to air-filled tires and solid rubber tires.
• For direct use in dry areas in the interior, e.g. warehouses, workshops, basement rooms etc.
• For layer thickness from 3 to 30 mm.

• For indoor and outdoor use.
• Wear-resistant and anti-slip uncoloured sealing of PCI Zemtec floor coatings and cementitious floors.
• For floors in production halls and storage rooms as well as offices and living quarters.
• Easier care and cleaning of sealed floors.

-

-

-

-

-